Radio over Fiber (RoF)
4 min read
Radio over Fiber (RoF) carries a radio-frequency signal over an optical fiber. The RF signal modulates a laser, travels as light, and is converted back to RF at the far end. For broadcast and film, it is the simplest way to put an antenna where it needs to be, hundreds of meters or several kilometers away from the receivers and transmitters.
How it works
A RoF link has three parts:
- an optical transmitter: the signal from the antenna or transmitter modulates the intensity of a laser;
- a single-mode fiber: it carries the light with very little loss;
- an optical receiver: a photodiode turns the light back into an RF signal, ready for the receiver, the splitter or the transmit antenna.
Transport is analog: the link carries the whole band, whatever the brand, the modulation or the number of channels. It does not depend on a protocol or on processing latency.
In the BSRF range, TX and RX refer to the optical direction. The FTX-1 is an optical transmitter: you connect an antenna or an RF source, and its signal goes out on the fiber. The FRX-1 is an optical receiver: it takes the light and delivers the RF signal.
Why fiber rather than coax
| Single-mode fiber | Coaxial cable | |
|---|---|---|
| Loss | ≤ 0.5 dB/km at 1310 nm, independent of the RF frequency | 10 m of RG223: about 3 dB in UHF, and more as frequency rises |
| Distance | Several kilometers | A few tens of meters before the link degrades |
| Weight | 100 m on a drum: about 2.3 kg | 100 m of RG213: about 14 kg |
| Interference | Immune to electromagnetic fields and ground loops | Picks up radiation from power lines and other RF cables |
| Isolation | Full galvanic isolation between both ends | Shared ground |
| Ageing | No oxidation | Connectors and shielding oxidize |
Fiber unwinds from a drum and deploys quickly on a film set, a stadium or an event site. On a noisy stage or industrial site, galvanic isolation removes parasitic coupling and grounding issues between the antennas and the control room.
Dynamic range and noise
A RoF link adds noise and distortion, like any RF stage. The key is the right trade-off between sensitivity and strong-signal handling. At BSRF, we design our own optical converters to optimize that trade-off. The AFB-250 offers 78 dB of dynamic range, from −90 to −12 dBm.
Our converters use DFB lasers, whose very narrow spectrum keeps the noise on the link low.
Wavelengths and multiplexing
As standard, BSRF converters work at 1310 nm and 1510 nm. Wavelength multiplexing, WDM or CWDM, is available as an option: several links then share a single fiber.
Applications
- Remote receive antennas: bring wireless mic antennas close to the stage, with the receivers at front of house. See Remote receive antennas over fiber.
- Remote transmission: place the IEM or IFB antenna far from the transmitters. See Long-range IEM over fiber.
- Multi-area coverage: serve several areas from a central rack, for both receive and transmit. See Multi-area radio mics and IEM coverage.
- Simplex link: bring the signal back from a camera position or an outdoor set. See Compact camera and ENG link.
Radio over Fiber is also used to carry TV, FM/DAB or GPS signals, in RF labs and in facilities where coax is not an option.
The BSRF range
| Use | Products |
|---|---|
| Simplex link | FTX-1 transmitter, FRX-1 receiver |
| Receive | AFB-250 dual-antenna box, with AFR-200, AFR-250S, ACH-642 or ACH-862 |
| Transmit | ATH-200 transmission base, with AFB-350 remote transmit box |
Not sure which setup you need? The wizard guides you in a few questions.