Radio over Fiber — Simplex receiver
FRX-1
The RF signal, recovered from fiber.
The FRX-1 is a compact simplex Radio over Fiber receiver. It converts a 1310 nm optical signal back to RF, from 80 MHz to 2.4 GHz, with two output modes: +30 dB amplified to re-emit an IEM, or attenuated 0 / −10 / −30 dB to feed a mic receiver, a GPS or a spectrum analyzer. 9 – 24 V supply, including through DC-feed. Designed and manufactured in France.
Bandwidth
0,1 – 2,4 GHz
IEM mode gain
+30 dB
IEM mode max output
+20 dBm
Attenuation
0 / −10 / −30 dB
Power
9 – 24 V DC
Power input
4 point conn or BNC
Highlights
Two output modes
IEM mode: the received signal is amplified by 30 dB (+20 dBm max) to be re-emitted through an antenna on the BNC. Attenuated mode: the amplifier is bypassed and the signal attenuated by 0, −10 or −30 dB to match the level to the end device (wireless mic receiver, GPS, spectrum analyzer).
+30 dB · 0 / −10 / −30 dB
Wideband, unfiltered
No filtering: 0,1 – 2,4 GHz in IEM mode, 0,1 – 2.4 GHz in attenuated mode (at −3 dB).
0,1 – 2.4 GHz
Built-in diagnostics
Four LEDs show the device state. An RF Peak LED flags an excessive RF level; a one-second push on SW shows the received optical signal level.
4 LEDs · SW 1 s
9 – 24 V power, two inputs
Powered through the downstream receiver's DC-feed on the BNC, or through the Hirose 4-pin DC input. 110 mA typ. in IEM mode, 54 mA otherwise (at 12 V).
DC-feed BNC or 4-pin conn
Compact format
A 33 × 33 × 113 mm, 140 g aluminium enclosure: fits in a waterproof housing, a cabinet or a flight case.
33 × 33 × 113 mm · 140 g
BSRF RoF ecosystem
Compatible with the FTX-1 transmitter and the AFB-250, over LC/APC single-mode fiber. 50 Ω impedance, or 75 Ω( at order) for video LNBs.
FTX-1 · AFB-250 · 50/75 Ω
In detail
The FRX-1 receiver converts an optical signal into an RF electrical signal. It brings the advantages of optical fiber transmission (low loss, wide bandwidth) together with the inherent benefits of the medium itself (lightweight, galvanic isolation).
It remotes unidirectional wireless systems: analog or digital wireless microphones, IEM, broadcast TV, multi-antenna video systems, FM/DAB radio, GPS and synchronisation signals.
The FRX-1 has two operating modes:
- IEM mode (amplified): the received signal is amplified by 30 dB, with a maximum output of +20 dBm. It re-emits a UHF signal, typically a pocket or rack IEM transmitter, through an antenna connected to the BNC.
- Attenuated mode: the amplifier is bypassed and the received signal is attenuated by 0, 10 or 30 dB. This mode receives low-level signals and matches their level to the end device (wireless mic receiver, GPS receiver, spectrum analyzer, etc.).
Both modes are unfiltered: 0,1 – 2,4 GHz in IEM mode, 0,1 – 2,4 GHz in attenuated mode.
Four LEDs on the enclosure display the device state. An RF Peak LED indicates when the RF signal is too strong. A one-second push on the SW button shows the received optical signal level.
The optical input is an LC/APC connector on single-mode fiber, at 1310 nm. The FRX-1 is powered from 9 – 24 V, either through the DC-feed on the BNC connector or through its 4-pin DC input.
It ships at 50 Ω, or 75 Ω at order for video LNBs. It is compatible with BSRF's FTX-1 transmitter and AFB-250.
Its compact aluminium enclosure allows integration into waterproof housings and cabinets.
Specifications
The numbers that matter.
Condensed excerpt. See the datasheet for detailed conditions.
RF
Fiber & power
Mechanical
Use cases
Wireless mics
Remote a mic antenna over fiber
Antenna → FTX-1 or AFB-250 → fiber → FRX-1 in attenuated mode → wireless mic receiver. Fiber replaces the long coaxial run, with galvanic isolation.
IEM
Re-emit an IEM at the far end of the fiber
IEM mode +30 dB, +17 dBm output: the FRX-1 locally re-broadcasts the signal of an IEM transmitter (pocket or rack) carried over the fiber.
Broadcast & instrumentation
TV, radio, GPS, sync, measurement
The same receiver remotes a TV or FM/DAB feed, a GPS or sync signal, a 75 Ω video LNB, or feeds a spectrum analyzer.
Configurations
Used in these setups
Documentation
Everything you need before buying.
Datasheets and user manuals available in PDF format.