Radio over Fiber — Dual-antenna transmitter box
AFB-250
Two HF antennas, over a single fiber cord.
The AFB-250 is a Radio over Fiber transmitter box for two receiving antennas. It converts two UHF 470 – 698 MHz signals to optical, each on its own single-mode fiber, inside a single OpticalCon Duo APC cord. Protected 12 V DC feed per input, 10 dB attenuator per channel, 78 dB min. dynamic range, 9 – 36 V power on XLR4. Aluminium enclosure for field use, to be used with an AFR-200, ACH-642 or ACH-862 base.
Bandwidth
470 – 698 MHz
Inputs
2 × BNC → 2 fibers · 1 Duo cord
DC feed
12 V / 200 mA per input
Dynamic range
85 dB
Attenuator
0 / −10 dB per input
LC/PC, WDM (one fiber)
Highlights
Two antennas, one cord
Each antenna is converted onto its own 1310 nm single-mode fiber. Both fibers travel in a single compatible OpticalCon Duo APC cord, or over two LC/APC. Optional: LC/PC and WDM (the two channel on the same fiber)
2 fibers · OpticalCon Duo
Protected DC feed, per input
12 V / 200 mA switchable independently on each BNC for active antennas, short-circuit protected: the DC-feed LED blinks on a cable or antenna fault.
12 V · 200 mA · per BNC
RF Peak and dynamic range
The RF Peak LED lights up from −12 dBm at the input. 78 dB dynamic range (−90 to −12 dBm), compatible with analog and digital modulation.
−12 dBm · 78 dB
10 dB attenuator per channel
Set at start-up on each input and stored, to reduce sensitivity and intermodulation near powerful transmitters.
0 / −10 dB · stored
9 – 36 V power on XLR4
Linear supply or battery on XLR4 (1 −, 4 +). 160 mA idle, 360 mA with one active antenna, 560 mA with two, at 12 V.
XLR4 · 9 – 36 V · 12 W
Rugged aluminium enclosure
Aluminium enclosure and connectors built for field use. Connects to an AFR-200, ACH-642 or ACH-862 base, an AFR-250S or an FRX-1.
155 × 180 × 70 mm · 1.3 kg
In detail
The AFB-250 remotes two receiving antennas over two single-mode optical fibers. Electro-optical components specially made for radio over fiber are used in this equipment. It is used with an AFR-200, ACH-642 or ACH-862 base.
Its rugged aluminium enclosure and its connectors are designed for field operation.
A 12 V / 200 mA DC feed, protected from short circuits, can be activated on each input individually to power active antennas. The DC-feed LED blinks in case of a short circuit in the cable or antenna.
An RF Peak indicator shows when the RF input level becomes too strong: it lights up from −12 dBm. Dynamic range is 78 dB, from −90 to −12 dBm, with analog or digital modulation.
A 10 dB RF attenuator can be engaged on each channel to reduce sensitivity and intermodulation. It is set at start-up and stored.
The optical output is a Neutrik OpticalCon Duo APC connector, 1310 nm, one fiber per antenna; connection through two LC/APC is also possible. Power is 9 – 36 V on XLR4 (pin 1 −, pin 4 +), from a power supply or a battery.
As with any RF equipment, a few rules apply to get the best from it: well-placed antennas, clean fiber, input level below the RF Peak threshold. Feel free to contact us about your project.
Specifications
The numbers that matter.
Condensed excerpt. See the datasheet for detailed conditions.
RF
Fiber & power
Mechanical
Use cases
Live / festival
Route two stage antennas back to the HF rack
Two antennas in the grid → stage-side AFB-250 → OpticalCon Duo cord → AFR-200 at the booth. 100 m of fiber: 2.3 kg on a drum vs 14 kg of RG213, with frequency-independent loss.
Broadcast / hostile site
Cross a noisy site, up to 10 km
Stadium, racecourse, industrial site: galvanic isolation between antennas and receiver, electromagnetic immunity of the carried signal. With a 5 dB optical budget, the base can sit 10 km away.
Fixed installation
Two rooftop antennas to a studio
AFB-250 in a weatherproof enclosure at the antenna foot (it must not be exposed to rain); fiber runs down to an AFR-200, ACH-642 or ACH-862 at the booth. Passive antenna: up to 10 m of RG213 before the box; active: up to 70 m.
Documentation
Everything you need before buying.
Datasheets and user manuals available in PDF format.