Radio over Fiber — Simplex transmitter

FTX-1

UHF over optical fiber, compact, two input modes.

The FTX-1 is a compact simplex Radio over Fiber transmitter. It converts an RF signal to a 1310 nm optical signal over single-mode fiber: in high sensitivity (470 – 690 MHz filtered, +12 dB) for wireless mic antennas, or in low sensitivity (0.1 – 3 GHz unfiltered, 0 / −10 / −30 dB) to plug a transmitter up to 50 mW straight in. Selectable antenna DC feed, 9 – 24 V supply. Designed and manufactured in France.

FTX-1 1
FTX-1 2
FTX-1 3
FTX-1 4
FTX-1 5

High-sensitivity mode

470–690MHz, +12dB

Low-sensitivity mode

0,1–3GHz 0-10-30dB

DC feed

12V-200mA

Impedance

50R(75R option)

Optical output

LC/APC·1310-1550nm · 1.5 dBm

Highlights

Two input modes

High sensitivity: 470 – 690 MHz filtered and amplified by 12 dB(LNA), for wireless mic antennas. Low sensitivity: 0.1 – 3 GHz unfiltered, with selectable 0, −10 or −30 dB. At -30dB on FTX-1 and +30dB on FRX-1 once can remote an IEM antenna.

+12 dB filtered · 0 / −10 / −30 dB

Selectable antenna DC feed

The input BNC can remote-power an active antenna: unregulated Vin, 200 mA. Switchable on or off to suit the connected antenna. Inside solder jumper can configure supply to 5V regulated.

Vin · 200 mA · on the BNC

Compact format

33 × 33 × 113 mm, 140 g aluminium enclosure, 9 – 24 V supply on a Hirose 4-pin connector: fits in a waterproof housing or a cabinet, right at the antenna.

33 × 33 × 113 mm · 140 g

BSRF RoF ecosystem

LC/APC 1310 or 1550 nm output at 1.5 dBm over single-mode fiber. Compatible with the AFR-250S, AFR-200, ACH-642, ACH-862 and ACF-802 receivers in high sensitivity, with the AFB-350 in low sensitivity, and with the FRX-1.

1.5 dBm · LC/APC single-mode

50 or 75 Ω

Ships at 50 Ω, or 75 Ω at order for LNBs and video chains.

50 Ω · 75 Ω · at order

In detail

Specifications

The numbers that matter.

Condensed excerpt. See the datasheet for detailed conditions.

RF

High-sensitivity band470 – 690 MHz (filtered)
Low-sensitivity band0.1 – 3 GHz
High-sensitivity gain+12 dB
Low-sensitivity attenuation0 / −10 / −30 dB
Max RF input+20 dBm
Noise figure< 2 dB typ.
Impedance50 Ω (75 Ω option)

Fiber & power

RF inputBNC · DC feed 200 mA
Optical outputLC/APC · 1310 nm · 1.5 dBm
Power supply9 – 24 V DC · Hirose 4-pin
Consumption90 mA @ 12 V, without DC feed

Mechanical

Dimensions33 × 33 × 113 mm
Weight140 g
HousingAluminium
CompatibilityFRX-1 · AFR-200 · AFR-250S · ACH-642 · ACH-862 · AFB-350
ManufacturingMade in France

Use cases

Wireless mics

Remote a mic antenna over fiber

UHF antenna → FTX-1 in high sensitivity (+12 dB filtered) → single-mode fiber → AFR-250S, AFR-200, ACH or FRX-1 at the booth. Fiber replaces the long coax run, with galvanic isolation.

IEM & transmitters

Plug a transmitter straight into the fiber

IEM transmitter up to 50 mW → FTX-1 in low sensitivity at −30 dB → fiber → FRX-1 in IEM mode or AFB-350 → remote antenna.

Broadcast & instrumentation

TV, radio, GPS, sync, measurement

The same transmitter remotes a TV or FM/DAB feed, a GPS or sync signal, a 75 Ω video LNB — or a measurement antenna to a spectrum analyzer through an FRX-1.

Documentation

Everything you need before buying.

Datasheets and user manuals available in PDF format.

Ready to replace coax with fiber?

Available by quote.