RF Distribution — Inline filtered amplifier
FA-1
Filter first, then amplify.
The FA-1 is an inline filtered amplifier, powered through the coax DC feed. 50 MHz cavity filter on four UHF blocks, BP / +6 / +9 / +12 dB gain, fail-safe: unpowered, it remains a passive filter. BNC, 94 × 20 × 24 mm, 100 g.
Blocks
[470 – 520] · [520 – 570] · [570 – 620] · [620 – 670] MHz
Gain
BP · +6 · +9 · +12 dB
Unpowered
−2 dB typ. (fail-safe)
Passive use
To filter a wideband amplifier
Power
DC feed 10 – 18 V
Form factor
94 × 20 × 24 mm · 100 g
Highlights
Filtering before amplification
A small cavity filter first, then a high-linearity amplifier: out-of-band interferers (walkies, DECT, Wi-Fi, GSM / 4G, intercom bases) are rejected before being amplified.
Cavity filter → amp
Four gain steps
A push button selects BP (filter only, no gain), +6, +9 or +12 dB to compensate the coax cable loss.
BP · +6 · +9 · +12 dB
Fail-safe
Unpowered, the FA-1 remains a passive filter: −2 dB typical, depending on the filter width. It also filters a transmitter or IEM output up to 1 W.
−2 dB typ. unpowered
Powered by the DC feed
No power lead: the FA-1 draws from the DC feed of a splitter (AS-62, AS-84, AS-122) or a receiver, and passes it through for an active antenna.
10 – 18 V · 100 mA · pass-through
Inline, on the cable
Machined aluminium housing, BNC in and out (N optional). Four standard 50 MHz blocks, custom filter on request.
BNC · 94 × 20 × 24 mm · 100 g
In detail
The FA-1 is an inline filtered amplifier, powered through the coax (DC feed). It protects receivers from RF interference (walkies, DECT, Wi-Fi, GSM / 4G, intercom bases) and compensates the cable loss. A small cavity filter, followed by a high-linearity amplifier, sits first in line: the signal is filtered before being amplified.
A push button selects the gain: BP (filter only, no gain), +6, +9 or +12 dB. The FA-1 works with passive or active antennas; the DC feed passes through it, from output to input, to power an active antenna.
Fail-safe: unpowered, the FA-1 works as a simple filter, −2 dB typical. It can therefore filter a transmitter or IEM output, up to 1 W.
Four standard 50 MHz blocks: 470 – 520, 520 – 570, 570 – 620 and 620 – 670 MHz. Custom filter on request, 20, 35, 60 or 120 MHz wide.
Powered by the DC feed of a splitter (AS-62, AS-84, AS-122) or a receiver, 10 – 18 V, 100 mA typical. BNC connectors, N optional. Machined aluminium housing.
Specifications
The numbers that matter.
Condensed excerpt. See the datasheet for detailed conditions.
RF
Power
Mechanical
Use cases
Dense RF
Protect receivers from interferers
FA-1 close to the antenna: out-of-band emissions are filtered before the cable and the splitter, the gain compensates the run.
Long cable
Compensate a coax loss
+6, +9 or +12 dB depending on the length, powered by the splitter DC feed. With an active antenna, the DC feed passes through the FA-1.
Transmission
Filter a transmitter output
Unpowered, the FA-1 is a passive filter that takes up to 1 W: at an IEM transmitter output, it cleans the transmitted spectrum.
Documentation
Everything you need before buying.
Datasheets and user manuals available in PDF format.